Westminster Omnibus – Sunbeam Sikh – JJ 9215

1933 Sunbeam Sikh with 64-seat Christopher Dodson bodywork, owned by Westminster Omnibus Co.
Photograph by ‘unknown’ if you took this photo please go to the copyright page.

Westminster Omnibus Co
1933
Sunbeam Sikh
Christopher Dodson (H36/28R)

In 1928, Sunbeam designed two prototype passenger chassis, a three-axle sixty-seven seat double-decker bus and a two-axle single-decker bus or coach. Two model names, ‘Sikh’ and ‘Pathan’, were adopted for them. They both had Sunbeam engines, but, despite their quality and reliability, very few were produced.
Here is a rare example of a Sikh, however, dating to 1933. It had a very handsome 64-seat body by that doomed London bodybuilder, Christopher Dodson, doomed because it concentrated business almost solely on London independents, due to disappear from 1933, when London Transport took them all over. You will notice the bizarre open cab with storm apron and protective cowling, insisted upon by Westminster’s managing director, who felt that enclosed cabs were unhealthy! The Westminster Omnibus Co. was taken over by LPTB in 1934, but the bus was barely operated by LPTB, as SM1, before being withdrawn from Sunbeam Rad Badge 2service.
In 1931, a Sikh chassis was modified as a trolleybus, which was an immediate success, creating a whole new passenger market which the bus chassis never penetrated.
To the right is the cheery radiator badge which Sunbeam used on their vehicles, which would have looked nice on the Sikh’s chrome one.

Photograph and Copy contributed by Chris Hebbron


Fascinating stuff!!
Dodson did, though build for operators outside London, albeit in small numbers.
Wolverhampton`s Guys come to mind.
Thanks.

Me again. I really enjoyed this post about Sunbeam. Was the open cab not something to do with London Police regulations at the time, where glass screens were deemed dangerous? Not sure, just asking!

John Whitaker


The LGOC had fought and won the windscreen battle in about 1931. It produced its prototype, it with a windscreen, but with an outside staircase, and ran it about a bit with a windscreen, the first. There was not fuss;maybe the notoriously conservative Metropolitan Police Commissioners didn’t notice! It then produced the first 49 production ones and the MPC DID notice, banning further production with windscreens, but not insisting that those already produced be converted. After about 12-18 months, the MPC, presumably being convinced that they weren’t a safety hazard, relented and windscreens were fitted retrospectively to later ones, which, after the first 150, then sported inside staircases, but were not objected to! Even in the mid-30’s the MPC stopped a production run of Central Area (red) single-deck Q’s with open front entrances in front of the front wheels, after an initial run of them was on the road! There was worry about passengers falling out and going under the wheels. I’m not sure that this was ever a problem, although it was resolved years later with knifejack doors.

Chris Hebbron


You are right, John, that Dodson did work other than for London ‘Independents’ (I actually feel that that were more against ‘The Combine’ the LGOC/Underground Group and therefore supported the ‘little feller’!). You mention work they did for Wolverhampton Corporation Guys, but, by coincidence, only today did I discover that Dodson bodied some thirty-odd AEC Regents delivered to Brighton, Hove & District in 1935. They were part of Thos. Tilling group, which, with its London roots, would have been well aware of Dodson’s existence. I’d love to see a photo of these buses to see the design of bodywork. Must start ferreting!

Chris Hebbron


Apropos the MPC and their regulations I was always under the impression that STL/STDs had no cab door was due these being declared verboten by the MPC. However the Sunbeam clearly has a door to its cab

Chris Hough


London Transport inherited quite a few buses with cab (half) doors and left them in situ, Chris.
I think the lack of doors in their own designs was more a case of being able to store buses in their garages closer to each other without doors. When RT1 came along, they’d got around the problem by having a sliding door inside of the bodywork line. With it, deservedly, came more comfort for drivers. STL’s did have concertina-type blinds to fill the entry gap, but they could only be used to protect the empty cab from the worst elements; you couldn’t drive with one down as it impaired vision. You’d have needed to be observant, and lucky, to ever see one down, though!

Chris Hebbron


Chris. It would be great to see a picture of the Brighton Tilling Regents with Dodson body. Dodson built some of the ST bodies for Tilling to Tilling design, I believe, but not the STL batch as far as I know. Dodson would make an interesting article in its own right if it could be researched. Small numbers of bodies were built for several municipalities as well as Wolverhampton, including Derby, Leeds. Another article would be the Pirates in London, with complete fleet lists. Dodson were by no means the only builders here, as Birch, Strachan and Brown etc. were also involved. Must get down to some homework!

John Whitaker


Yes, John, please do!
Meanwhile, I will do some digging to see if I can trace photos of any of the BH&D Dodson-bodies AEC Regents.

Chris Hebbron


Chris. The complete registration for Westminster Sunbeam Sikh (H36/28R) in photo (taken at Edmonton) is JJ 9215. It was licensed to run on London Routes 76 & 73, entering service FEB 1933 as the largest running London bus at the time. It was the last bus design by Dodson Ltd. before exiting the business in April, 1933. The Dodson family originally made horse buses from the mid 1800’s until motorized buses came about after 1900. I’m related to the family and researching the business so I really enjoy finding posts and photographs like this!

Phil Dodson


I’m sure it’s true what they say – history begins on your birthday.
I’m a child of the fifties and although I stretch it to post-war forties, it really all starts for me in 1952 with two of my favourite batches of buses, the STD PD2s and Regent IIIs, delivered in 1952.
I then began to back track – through the excellent British Buses since 1900 and John Aldridge. Sunbeam attracted my attention because they were MOTORbuses and John Aldridge implies that the quality of build was so high that they were too good and therefore too expensive for the general market. Likewise with Dodson bodies. No PSV historian is ignorant of the name, but few of us will have had first hand experience of their products.
When some of us are in our wheelchairs going misty eyed about AEC, Leyland, Roe, Weymann – or whoever – what will that mean to our grandsons and granddaughters? Food for thought – or is just too depressing?

David Oldfield


How wonderful that a modern Dodson is researching the business!. I do hope the findings become available, as I have recently come across several instances of Dodson bodywork outside London.
Cedes Stoll tracklesses.
Peterborough and District Leylands.
Derby Guy Invincibles?
Some of the ancestor fleets of EYMS in Hull
Wolverhampton Corpn. (plenty there)
Many more mid 1920s on Dennis 4 ton and Leyland G series type vehicles. Leeds Corporation.
There must be many more out there…feel like searching and telling everyone?

John Whitaker


I’d say, Phil, that we are as delighted to find a member of the Dodson family as you are to find the posting. Maybe you could post a potted history of this well-regarded company, with a couple of photos, for us all to enjoy. If the above photo was the last Dodson design, the company went out on a real high – it is very attractive. Did the company come to a complete halt in 1933, or did it have other irons in the fire which kept it going?
[Thx for the full registration – now updated].

Chris Hebbron


Just thought of 2 more Dodson customers.
Hastings Tramways
West Bridgford UDC (1914 Dennis)
There has to be many more.

John Whitaker


On the Dodson theme, Portsmouth Corporation started it’s motorbus fleet with 10 Thornycroft J’s in 1919, which had locally built Wadham bodies. But in 1926/27, these were rebodied by the Corporation, using ex-LGOC B-type bodies, built by Dodson. They also bought a complete B-type, with a Dodson body (this did not last long).
On withdrawal by c.1929/30, one of the Thornycrofts (No.10, BK 2977) with it’s Dodson body was preserved, and is fortunately still with us. It is located at the Milestones Museum in Basingstoke, and looks extremely attractive in a contemporary setting of a street scene with other Thornycroft commercial vehicles of that era.

Michael Hampton


Re the Dodson theme, the preserved Portsmouth Thronycroft J at Basingstoke is registered BK 2986 (not BK 2977). Apologies for error in my memory of the batch, which was 1-10 (BK 2977-BK 2986).

Michael Hampton


Chris. Christopher Dodson retired and closed up the business in 1933 due to LPTB Act which took away his "Independent" bus operator customers. The LGOC had hindered bus competition and his business for years which is why he was so devoted to supporting the needs of independent operators and against "The Combine" group as you mentioned.
Dodson Ltd. also built trolleybus bodies from 1912-1933, mainly for Keighley, Wolverhampton and Derby. Christopher’s brothers also started a bus service on the Isle of Wight in 1921, Dodson & Campbell Ltd, which became Dodson Bros Ltd/Vectis Bus Co. in 1923. Christopher was also a director in that company which merged with Southern Railway in 1929 to become Southern Vectis. All their buses had Dodson built bodies of course up until 1932 when they retired and sold their interest in the company.

John interestingly mentioned that Hastings Tramways was a Dodson customer. Dodson built 8 trolleybuses for Hastings in 1928, one of which,(DY 4965), still survives today. Restored and known as "Happy Harold" it has been fitted with a diesel engine to run as a bus. There is a short 1928 film clip of when the 8 Hastings trolleybuses were put into service that can be watched at this You Tube link.
"Happy Harold" is the trolleybus observed on right side from :18 to :43 seconds into the film clip.

Phil Dodson


Thanks Phil for the Utube film!!! How about that!!!
Please inform us all when you have completed your investigations. I would love to know of all the Dodson bodies, wherever they went. They had a very distinctive air about them, and the Sikh was by no means the only modernity item produced. Wolverhampton,s 1929 batch of Guy BTX had a much more modern body style, as did some other London Pirates. There was a Maudslay 4 wheel double decker with one of them if I remember, dated 1932/3

John Whitaker


29/08/12 – 10:33

Fascinating thread. I wonder if anyone has information regarding the Westminster livery carried on the Sunbeam Sikh? Was it red/cream?

Colin James


29/08/12 – 12:15

Maybe, if Phil Dodson sees this, he could tell us. Looking at this vehicle again, it’s got to be one of my favourite buses ever. What a shame that Dodson packed up and never built any more of them.
Could someone with DVLA access give the subsequent history of the vehicle?

Chris Hebbron


29/08/12 – 14:54

Didn’t it pass to Derby Corporation for a short time, or was that another one?

John Whitaker


30/08/12 – 07:03

The PSVC lists JJ 9215 as withdrawn by London Transport in 1934; to G J Dawson, SW9 (dealer) 5/35; Wigan & District Subsistence Production Society, Wigan, 1/37; G Pudifer, Liverpool, 9/39; J Routledge, Seaforth, Liverpool (dealer) 11/39, and scrapped.
According to Blacker, Lunn, & Westgate (London’s Buses Volume One – The Independent Era 1922-1934) Westminster’s livery was red and cream. The absence of a windscreen was apparently a peculiarity of one of the managing director, Mr Rich, who thought that windscreens were unsafe and that the draughts they created were bad for drivers’ health. JJ 9215 was reported to be a smooth runner but had a tendency to boil quickly.
There was a second Sikh built in 1931 with an older style of Dodson body for the Sphere Omnibus Co, but it did not enter service with them, although it was successfully submitted to the Police for testing. It became UK 7456 and was demonstrated by Sunbeam to Mansfield District, Midland General, and Derby, Birmingham, and Northampton Corporations, and was scrapped in 1940. Presumably this is the vehicle to which John refers.

Michael Wadman


31/08/12 – 07:35

Thanks muchly, Michael, for answering the queries Colin, John and I raised and even more!

Chris Hebbron


31/08/12 – 09:37

So sad, the number of manufacturers (vis Gilford and Dodson) who failed through no fault of their own, but rather because their customer base simple dried up or disappeared. What price a Euro 5 Gilford with Dodson body?

David Oldfield


31/08/12 – 09:38

Yes Michael, many thanks for the info on the 2 Sikhs.
There is something truly magnificent about the "big buses" of this era, and I am reminded of that marvellous machine introduced by Wolverhampton Corporation in (1929?). Again, with a Dodson body, but a 6 wheeled petrol electric Tilling Stevens. I only have a photo in a book; otherwise I would post it !

John Whitaker


31/08/12 – 16:02

The Westminster Omnibus Co. Sunbeam Sikh SM1 was withdrawn by the LPTB on 10 July 1934. This site gives a wealth of detail about the bus models of the Sunbeam company:- www.historywebsite.co.uk/Museum  In all its product ranges, bicycles, motorcycles, cars and buses, the Sunbeam company was synonymous with exceptionally high quality in keeping with the principles of the founder, John Marston, and almost all components were produced in house. This was reflected in the retail prices, and, in the depressed markets of the inter war years, sales were limited. The various parts of the Sunbeam group fell into different hands, though the name lived on for some models of motorcycle, motor scooter, car, and, of course, trolleybus. At least the trolley manufacture, ultimately part of Guy, remained in Wolverhampton to the end.

Roger Cox


16/12/13 – 07:23

Re John W/Michael W’s post on 29/8/12, I’ve found other, slightly conflicting info on the Derby Corporation Sikh. No. 44 was an ex-Sunbeam demonstrator, registration UK 7456 (chassis K10123) which dated from 1929. Its Dodson body seating was a smaller H35/32R, presumably to an earlier style, since the Westminster one was larger and the 1933 style. It went into service with Derby in 1933 and was also withdrawn in 1939.

Chris Hebbron


16/12/13 – 09:25

Thanks Chris for the TSM and Sunbeam detail which I have noted. You are correct in saying the Derby Sunbeam was of the earlier Dodson body style. I have seen a photo but cannot remember where it was. In "Looking at Buses" by G. Hilditch (I Think!)
Loads of Senior Moments!
I am now following Thornycroft. Have you seen the magnificent 6 wheeler photo on the Thornycroft site, with a camel roof body, which is a bit "Hall Lewis" looking. Also, trying to unearth photos of the 4 wheel BC Boadicea model as supplied to Southampton etc. This explosion of competition from 1929 to 1932 provides enough material for someone to write a book.
It would need someone a lot more technical than me though, a mere ageing enthusiast!

John Whitaker


17/12/13 – 06:51

The engine of the Sikh was an advanced and powerful overhead valve unit of 7.98 litres, developing 142 bhp at 2,400 rpm., which drove via a friction clutch into a four speed gearbox. The same engine was fitted to the more successful Pathan single deck model. Such a powerful engine must have given the Sikh and the Pathan remarkable road performances by any standard, certainly well above the norm for the early 1930s, though probably at a cost in fuel consumption. The Westminster Sikh weighed 7 tons 5cwt 3qtr, which seems remarkably light, and entered service in London in the week commencing 20th February 1933; the absence of a windscreen was entirely due to the rigid opinions of the Westminster company’s managing director, as the Met Police had capitulated on cab windscreens by this time. Only three Sikhs were made, the Westminster one being the second in production. In view of the imminent introduction of the London Passenger Transport Act on 1st July 1933, it is surprising that Westminster should have purchased such an expensive piece of capital equipment at so late a date. Almost inevitably, the solitary Sikh SM 1 did not survive long in the standardised world of the LPTB, being withdrawn in 1934 and disposed of on 16 May 1935. Its subsequent fate is unclear. As Michael Wadman and Chris Hebbron state above, the very first Sikh was cleared by the Met Police for use by the Sphere Omnibus Company on routes 73 and 76, but it never entered service, becoming instead a Sunbeam demonstrator and vanishing in the early years of WW2. The third Sikh was converted to a trolleybus, and opened up a much more successful market, though the original Sunbeam Company was not to see much of the benefit. In 1934, STD (for Sunbeam Talbot Darracq as then was) went into receivership, and the Rootes group picked up most of the assets.

Roger Cox


18/12/13 – 06:21

John, the best source of information on Thornycroft is the volume published in 2001 in the Ian Allen Transport Library (ISBN 0 7110 28141) written by the ever dependable Alan Townsin, who once worked for the firm himself. Details and photos of the bus models are there aplenty. Unfortunately, the book has no photos of a Southampton BC Forward, but there is a picture of Southampton’s rare HC six wheeler and another of a Daring. A picture of a United BC Forward may be found on this site under ‘Best Bits – A United Line Up’.

Roger Cox


18/12/13 – 14:14

Thanks Roger. Will look up the Thornycroft book, especially with the HC 6 wheeler being there! I remember them having English Electric bodies very similar to the Pompey Karriers.
Fascinating era to study!

John Whitaker


 J 9215_lrVehicle reminder shot for this posting


06/12/14 – 06:49

Sunbeam Sikhs are rare: photos even rarer! The link below shows a 1931 Midland District Sikh of 1931. What a dramatic difference is demonstrated by a mere two-year gap! //midlandgeneralomnibus.weebly.com/mansfield-district-buses.html

Chris Hebbron

Bournemouth Corporation – Sunbeam MS2 – BRU 8 – 200

Bournemouth Corporation - Sunbeam MS2 - BRU 8 - 200
Copyright Ray Soper

Bournemouth Corporation
1935
Sunbeam MS2
Park Royal O69R

This shot is from the Ray Soper ‘Gallery’ contribution A Trolleybus tour in Bournemouth click on the title if you would like to view his Gallery and comments to it.
The shot is shown here for indexing purposes but please feel free to make any comment regarding this vehicle either here or on the gallery.


16/07/13 – 07:58

This looks like a ‘special’ on the Christchurch turntable. The turntable still exists in an office car park.

Grahame Arnold

n

Bournemouth Corporation – Sunbeam MS2 – ALJ 986 – 202

Bournemouth Corporation - Sunbeam MS2 - ALJ 986 - 202
Copyright Ray Soper

Bournemouth Corporation
1935
Sunbeam MS2
Park Royal O69R

This shot is from the Ray Soper ‘Gallery’ contribution A Trolleybus tour in Bournemouth click on the title if you would like to view his Gallery and comments to it.
The shot is shown here for indexing purposes but please feel free to make any comment regarding this vehicle either here or on the gallery.


16/07/13 – 08:02

Lovely shot of the ’38’ summer-only circular service travelling along Barrack Road. These services were aimed at visitors although locals like me also used them if convenient.
The regular year-round ‘circulars’ in Bournemouth at that time were routes 33 and 34, usually the preserve of the B.U.T. trolleys

Grahame Arnold

Bournemouth Corporation – Sunbeam MF2B – WRU 261 – 261

Bournemouth Corporation - Sunbeam MF2B - WRU 261 - 261
Copyright Ray Soper

Bournemouth Corporation
1958
Sunbeam MF2B
Weymann H63D

This shot is from the Ray Soper ‘Gallery’ contribution A Trolleybus tour in Bournemouth click on the title if you would like to view his Gallery and comments to it.
The shot is shown here for indexing purposes but please feel free to make any comment regarding this vehicle either here or on the gallery.


17/07/13 – 06:50

A nice view from the upper deck of a passing vehicle. This trolleybus is at a stop in Avenue Road where the Winton & Charmister trolleybus routes all departed from. The Council kiosk behind stood for many years, and beneath it were the local public WCs. Further up Avenue Road were the BCT offices at ‘Fairlight Glen’; this address appeared on the BCT Public timetables of the period.
Note the lovely GPO stamp machines and letterbox behind the bus stop; all very modern at that time. 4d for second-class!
Avenue Road was one-way at that time and had several trolleybus stops. It also had a ‘passing loop’ in the overhead to enable ‘through’ trolleybuses to pass those waiting at the stops. Route 25 ran along this road on its way from Westbourne to Boscombe. This bus on the 26 would have turned via ‘The Triangle’ just up the road.

Grahame Arnold

Bournemouth Corporation – Sunbeam MF2B – 296 LJ – 296

Bournemouth Corporation - Sunbeam MF2B - 296 LJ - 296
Copyright Ray Soper

Bournemouth Corporation
1961
Sunbeam MF2B
Weymann H65D

This shot is from the Ray Soper ‘Gallery’ contribution A Trolleybus tour in Bournemouth click on the title if you would like to view his Gallery and comments to it.
The shot is shown here for indexing purposes but please feel free to make any comment regarding this vehicle either here or on the gallery.


26/04/12 – 11:35

This very vehicle No.296 was the first to enter service with the light green lining in 1962. For more detail see my comment here. 

mf2b


17/07/13 – 06:48

This lovely shot is taken at the upper end of Gervis Place, I would say, or possibly opposite the Pavilion. The ‘Christchurch’ routes all departed from this end of the Square

Grahame Arnold


05/11/13 – 10:34

I have a photo of myself driving bus no 188 in November 1973 which was a Daimler. also a photo of bus no 213 a Leyland Atlantean. It was my last day as a driver so had some photos taken as a keepsake if anyone would like a copy please forward e.mail address.

John Kilroe

Hull Corporation – Sunbeam MF2B – RKH 102/15 – 102/15

Hull Corporation RKH 102 Sunbeam MF2B Trolley Bus

Hull Corporation RKH 115 Sunbeam MF2B Trolley Bus
Photographs by ‘unknown’ if you took these photos please go to the copyright page.

Kingston upon Hull Corporation Transport
Sunbeam MF2B
1954 (102) 1955 (115)
Roe H30/24D

The final batch of Kingston upon Hull Corporation trolleybuses, comprised a batch of 15 production and one prototype Sunbeam MF2B’s with Roe 54 seat highbridge bodywork. Due to the date of the prototype entering service in 1953, the whole batch were known as "Coronation" They were designed by the General Manager of KHCT, Mr G H Pulfrey, and the bodies were built to his design by Charles H Roe, of Crossgates, Leeds.
They were designed for one man operation, but in fact were never so used. The bodies were of 8′ width and featured front entrances, ahead of the front wheels and a central exit; internally they were fitted with two staircases, and a periscope was fitted to allow the driver to see how may seats were available on the upper deck, without leaving his seat. Another new feature in Hull was the use of automatic trolley retrievers, to assist with rewiring dislodged trolley poles.
It is believed that the 16 "Coronations" were always allocated to Cottingham Road Garage, working the Chanterlands Avenue and Beverley Road routes (61 and 63). Their working lives were comparatively short being only 9 to 11 years. Despite their short lives, none were sold for use elsewhere, but some Motors and electrical equipment were sold to Bradford, the remainder going for scrap. It is a shame that none of these fine vehicles were preserved.
The two photographs show number 102 (RKH 102), working route 61 on Chanterlands Avenue at the Goddard Avenue turning circle, this was the terminus of the 65 short working. It is on the outward journey. The second photograph shows sister vehicle 115 (RKH 115), In Ferensway, Hull city centre, passing the (then) Royal Station Hotel, whilst working a special service. The streamline livery of Hull Corporation, is shown to best effect on these vehicles.

Photograph and Copy contributed by Keith Easton

What superb vehicles these Hull trolleybuses were, and to a unique design too. I remember them so well from my RAF days at Patrington (1955/6) and of course they were in their prime then. What a tragedy that, if they had to be withdrawn early, they couldn’t have been sold as complete runners to Bradford. With five or six years remaining for the Bradford system they would have been a fine sight in the lovely blue and cream of the last trolleybus network in the Country – ah well, we can dream.

Chris Youhill

Ref the Bradford comment, lets play ‘what if’s’ for a moment!.
If we assume that going from a two door to front door only layout ( i.e. as per Atlantean or Fleetline) would gain 10 seats – 2 x doubles on each deck in place of the stairs + a double in place of the door that would take it up to a 64 seater. Extend the body in the rear overhang by one full bay would gain another row of seats on each deck which now gives us a 72 seat 30 foot bus. Sounds drastic?, perhaps – but not as drastic as building a complete new body which is what Bradford did only two years earlier on the ex Mexborough chassis and even then only finishing up with a vehicle with less seats at greater cost. Perhaps we could then have also seen a One Man Operated trolleybus as originally intended?.

By the way – is it me or does anyone else think that the Coronations bear a strong resemblance to the AEC Q type trolleybus?

Andrew

I talked, a month ago, about AEC cul-de-sacs – but often a design is years ahead of itself. Could be this is just such an example.

Sometimes a vehicle morphs into someone else’s.
Daimler Roadliner   became:
Dennis Falcon V     became:
Duple 425             became:
Dennis R series

The Bristol RE became:
Ward Dalesman GRX and Dennis Falcon H/HC

Did you know, though, that the last Sunbeam motor bus was a Sunbeam Regent – the trolleybus side was sold separately!!!

David Oldfield

The decision to abandon Hull’s trolleybus network was made in 1959, but although the trolleybuses were making a healthy profit, passenger numbers were on the decline, as more journeys were being made into the B zone, whilst the trolleybuses were only operating within the A zone. In 1934, the well known co-ordination agreement with East Yorkshire took effect and the tram routes in the B zone were abandoned and replaced by motor buses. Hull could have had a much larger trolleybus network, but for two reasons. The first being the co-ordination agreement, and secondly the cost of extending the overhead equipment. Had the trams not been curtailed, the trolleybuses would almost certainly have operated within the B zone also. This could have also seen EYMS trolleybuses, what a thought!

Keith Easton

A wonderful thought indeed Keith – but I imagine no through workings to Beverley as that would have been pushing the clearance miracle under The Bar just too far !!

Chris Youhill

Oh, I don’t know, Chris. You remember the principle of the conduit trams in London!

Stephen Ford

Indeed Stephen, I remember the London conduit system very well. On frequent childhood holidays in South London I spent many hours wonderment in watching the procedure for changing from overhead to conduit at the south end of Streatham High Road on the A23. Any such trolleybus scheme for the Beverley Bar would, I’m afraid, have been stamped on heavily at the planning stage in that very conservative ancient town.

Chris Youhill

With all the hoo-ha over satellite dishes in the Avenues, from the residents association, I very much doubt that trolleybuses would be allowed along Chanterlands Avenue these days; let alone Beverley! Seriously, though, trolleybuses working around Hessle, Anlaby, Willerby and Cottingham would have been serious contenders for, perhaps circular, services to and from Hull.

Keith Easton

As an aside, I notice that Hull was another (trolley) bus organisation which did not really consider visitors to the city in terms of blind displays. Enormous numbers and an almost begrudging display of the destination, and this was the ’50’s! Whilst it could be argued that pre-war London Transport intermediate blind displays were over the top, they did at least consider the native and visiting passenger. Smart vehicles, though, and nice to see a general manager ploughing his own furrow.

Chris Hebbron

Hello Chris, please see my comments on the AEC Regent III, HAT 471, for an explanation of Hull’s post-war blinds. Pre-war blinds in Hull were really quite informative, giving inner and outer terminals, with the main road(s) traversed, and the route number. For an example see the rear blind on Sunbeam W, number 80 (that will be posted 25/09). I must agree with post-war blinds though, but as a native Hullensian, we knew which route numbers went where, but it was not easy for visitors, but most Hull folk were friendly anyway.

Keith Easton

Interesting to read that these vehicles were intended for one-man-operation, given that this was not to be legal on double deckers for another 12/13 years; I would have thought that in 1953 O-M-O was fairly uncommon even on single deckers!

Dave Towers

The Coronations were also used on service 62 – I used service 62 every day to go to school. No. 101 did a six week stint on every route when it first entered service although the Hessle Road stay was cut short because it couldn’t cope with the very heavy loads.
The photo of 115 shows in Paragon Square on the DOLRS tour which covered every route and garage. No. 115 was newly repainted. There are other photos which show it in Holderness Road garage and at North Bridge.

Malcolm Wells

26/04/12 – 06:17

Keith, I think that RKH 102 is pictured at the end of Chanterlands Avenue, entering the Bricknell Avenue roundabout, just before it reaches Goddard Avenue. In the mid-1950s the roundabout was quite new, prior to which the trolleybuses used to sweep majestically round the bend into Chants North! The site of the pre-fabs in the background is now occupied by sheltered homes and the bus shelter at far right is now the Rainhill Road stop (opposite Murrayfield Road).

Malcolm Burke

Hull Corporation – Sunbeam W – GRH 356 – 80

Kingston upon Hull Corporation Transport - Sunbeam W Trolleybus - GRH 356- Black& White

Kingston upon Hull Corporation Transport - Sunbeam W Trolleybus - GRH 356- Colour

Kingston upon Hull Corporation Transport
1945
Sunbeam W
Roe H31/29R

In order to undertake the final tram replacement along Hessle Road, in 1945. The final trolleybus route commenced on 1st of July. To operate this route 18 trolleybus chassis were purchased from Sunbeam. The first 12 were bodied by Brush of Loughborough, but the final 6 were bodied by Leeds-based Charles Roe. Number 80 is one of this final batch, which entered service in November, 1945.
Originally the seating layout was H30/26R, but along with most of the earlier trolleybuses it was upseated to H31/29R configuration in 1948.
The black and white photo shows no 80 operation along Anlaby Road, near to the Boulevard, the latter being the terminus of route 71, which, incidentally, had the only trolleybus reverser on the whole system, located at Malm Street. 80 is operating the main 69 service, in the outbound direction. The blinds are of interest, as the front blind is the 1942 wartime version, but the rear blind is the original black on white type. It is carrying a healthy load of passengers despite being on a 5 minute headway.
The colour photo shows it returning to the city centre on Newland Avenue service 62. It is seen in King Edward Street nearing the terminus. Considering the austerity of the period when they were built, they are a very handsome vehicle.

Photograph and Copy contributed by Keith Easton

The front blind in the top photograph is not the wartime version – the wartime version was a large number only – the number and via only display was agreed in December 1945 and gradually introduced from 1947. The rear blind is not as originally made as the Anlaby Road service was to be numbered 65 (Hessle Road would have been 66) but the renumbering in February 1942 changed this to 99. The blind was changed simply by altering the number.

Malcolm Wells

Hi Malcolm, many thanks for your input clearing up details on trolleybuses, a lot of the information was mainly from memory, and it ain’t always what it used to be!

Keith Easton

The reference to service 99 in my previous comment was a typing error – it was 69.

Malcolm Wells

Hull`s first batch of trolleybuses were Leyland TB4s with composite Weymann bodies. Subsequent batches by Crossley and Leyland were bodied by East Lancs and Cravens, both well known for metal framed bodywork. If this is so, does anyone know why Hull changed policy here, only to revert to timber framing (Roe) post war?

John Whitaker

My initial reaction would be that Hull’s East Lancs and Cravens bodies were timber-framed. I don’t know in this specific instance, but it was generally preferred in trolleybuses as metal-framed trolleybuses had to have low voltage (instead of traction voltage) lighting and in those days that required a motor-generator set which was extra weight, expense and something else to maintain, so not preferred.
Huddersfield had many East Lancs-bodied trolleybuses but only ever one metal-framed one. The motor-generator set and the associated noise was the reason why (I learnt this from Roy Brook’s excellent book on that system.)

David Beilby

I`m pretty sure you are right Dave re the Hull Craven and East Lancs trolleybus bodies, although they must have been to special order to be timber framed.
Motor generator sets are not the only way of lighting a trolleybus with metal bodies though, Bradford, from 1935 dispensing with this item but still retaining English Electric and Weymann all-metal bodies. I can supply more detail on this if anyone is interested, but Bradford was a trolleybus pioneer in several ways at this time.

John Whitaker

The debate about use of timber &/or metal framed bodies for trolleybuses is both interesting and, for the most part, true. The premise, however, isn’t. It presupposes that the move to Roe composite from any other metal was retrograde. The fact is that Roe composite bodies right up to the end (1968) were far better quality than many metal framed bodies – and that includes Roe’s own (Park Royal designed) metal framed bodies which gradually replaced them.
Evidence also suggests that the quality of Craven bodies could be suspect and that rebodying of such vehicles was not unknown.

David Oldfield

Further to David Oldfield’s comment, Nottingham had a series of 45 Craven bodied AEC Regents supplied in 1938, and I understand they were always regarded as much inferior in build quality to the earlier (1936) Metro-Cammell equivalents. And the inferiority of the Craven bodied first generation DMUs for British Railways was legendary!

Stephen Ford

Bradford was indeed a pioneer with trolleybus development, as it worked with the English Electric Company to produce a new trolleybus control system called series dynamic and rheostatic braking (SD) in 1936. This SD control system became the standard adopted by the Ministry of War Transport for the Sunbeam W/Karrier W trolleybuses built from 1943 onwards. Most of the post war trolleybuses built had the SD system of control, which was the case with the London Transport BUT 9641T BUT Q1 class. These were significantly different to the London prewar fleet that all had regenerative braking control.

Richard Fieldhouse

No premise intended David!
Horses for courses and all that. I am one of the greatest Roe admirers, as were Bradford Corporation, with their BUTs 740-751 !

John Whitaker

03/02/12 – 06:26

Pontypridd Urban District Council Transport needed extra buses during World War II for the local town services (electrified) as the petrol buses were in great demand to transport workers to the then rapidly expanding Treforest Industrial Trading Estate, (war effort) near Pontypridd.
The Trolleybuses ran a regular route from Treforest village 2 miles south of Pontypridd (not to be confused with Tref Ind Est, 4 miles south of Pontypridd)through to Pontypridd and on to Cilfynydd (pronounced Kilvunith for non welsh speakers) 2 miles north of Pontypridd where the buses turned for the return journey.

Mike Ashcroft

05/02/12 – 06:44

The Hull Cravens bodies on Crossley TDD4 chassis were of composite construction in accordance with Hull Corporation Transport’s specification TC2 as were the East Lancashire bodied Leyland TB7s. The Cravens bodies received major overhauls in the early 1950s (no. 46 excepted which was withdrawn in December 1954). In addition, several received new or rebuilt platforms by 1959.
Hull’s Sunbeam F4s nos 91-100 had 8 feet wide Roe bodies similar to Bradford’s 740-751 but the interiors of the Hull vehicles were far superior to the Bradford bodies. I was surprised on the first visit to Bradford in 1961 (when 91 to 100 were still in service in Hull)at the difference.

Malcolm Wells

Walsall Corporation – Sunbeam F4A – XDH 72 – 872

Walsall Corporation - Sunbeam F4A - XDH 72 - 872
Copyright Tony Martin

Walsall Corporation
1956
Sunbeam F4A
Willowbrook H36/34R

Walsall Sunbeam F4A, Willowbrook bodied trolleybus, 872  XDH 72.
Seen leaving Bichills Depot on the evening of 3rd October 1970, having dropped off the guests it carried and is now making the last run ‘under the wires’ on a public road by a Walsall trolleybus.
At the wheel is Mr R. Edgley Cox, Walsall’s well known general manager.
The bus had been owned by West Midlands PTE since October 1969 and is now at Sandtoft Trolleybus Museum.

Photograph and Copy contributed by Tony Martin


13/11/12 – 17:30

How very atmospheric! Thanks for sharing.

Pete Davies


13/11/12 – 17:31

TDH 912

Here is a picture of fellow Walsall Corporation Sunbeam/Willowbrook trolleybus No. 862, which now resides at the Black Country Museum, Dudley, where I photographed it on 3 June 2010.

Roger Cox


14/11/12 – 07:31

Distinctive, if not that attractive vehicle, IMHO. I do recall being surprised at seeing one of these running around Portsmouth, when there was a municipal transport conference on at the Guildhall around 1955-56. It certainly turned some heads, with its blue livery amongst the familiar maroon/white natives!

Chris Hebbron


14/11/12 – 07:31

Although these vehicles were something of an ‘ugly duckling’ there was something charismatic about them and I always liked them. I have often wondered how long Walsall would have continued to run trolleybuses if the West Midlands PTE had not been set up. Having taken over in 1969 the PTE couldn’t wait to be rid of the trolleys and the drafting in to Walsall of large numbers of Birmingham ‘standards’ hastened the conversion. If my memory serves me correctly this left just Teesside and Bradford still operating trolleybuses and I was present at the last day for both these systems.

Philip Halstead


15/11/12 – 11:12

I’ve always thought that Mr Cox, if he had the chance, would have made sure Walsall’s trolleybuses were the last, even if only by an hour! Of course, early 1972 was one of the periods when power cuts affected many parts of the country.
More of my ‘old bus’ photos on www.flickr.com

Tony Martin


17/04/13 – 07:20

I have a photo somewhere of 864 running route 20 Eastney in Portsmouth – I’ll look to uploading it soon.
If only Walsall had retained the wiring on one of the circular routes and one each of the vehicles…

jvs


05/06/13 – 05:51

Almost certain Ron Edgley-Cox is sat on the contactor cabinet in this shot – but he was most certainly at the wheel when it came back

jvs


12/07/13 – 07:56

As mentioned the N/S cab contains the large contact box and keeps it well protected. These were the first 30ft trolleybuses to be placed in service on two axles and weighed in at I think, 7 Ton 5 cwt. 832 is a nice one to drive and very user friendly.

William Parker


15/07/13 – 08:14

It was perhaps surprising that Mr Edgley Cox opted for this design since in May 1954 he sent a drawing to the Ministry of Transport for a longer 62 seat version of Hulls Coronation trolleybuses. He fully supported G H Pulfrey’s views on one-man operation and saw this as a good design although his version lacked a central staircase despite having a central doorway as well as the forward doorway.
He also advocated longer single deck trolleybuses.

Malcolm J Wells


11/09/13 – 16:30

Great night picture. I passed out for my green badge on Walsall’s trolley buses (Was it Mr Clarke) and was so sorry to see them go. The colour of those buses at night was strange due to the street lighting. Frosty early mornings was like bonfire night sparks and flashes lighting up the streets. That bamboo pole was in regular use with me pulling the wrong change over, Great buses indeed yes I loved those trolleys. That vehicle they used to come and repair and tape up the damaged poles was an oddity lol. Happy days. I must go to the BCM to see one again. The Daimler Fleetline’s was a lot slower, shhhh, early morning Pratt’s bridge/Walsall you could get a lick on. Thanks for the chance to see those pics, lovely site.

Frank


14/02/14 – 13:29

Edgley Cox tried to get towards one man operation when he converted three trolley buses from rear entrance to front entrance. They were 875, 876, 877, These were the first buses I worked on when I started a an apprentice bodybuilder in 1961.

Stewart Poxon


16/02/14 – 07:53

There was a rumor that Walsall purchased Bournemouth 300 in 1969, for some sort of electric to diesel conversion experiments. Did this happen or was 300 scrapped like the rest?

Lewis Esposito


04/04/14 – 06:22

Walsall did have Bournemouth 300 (300 LJ) at their works in 1969, the plan being to make modifications so that it would be suitable for OMO. The plan was to buy 29 of these modern trolleybuses from Bournemouth at a total price of £4,000. One report says that the electric motors were to be removed and replaced by diesel engines. For more search Flickr "300LJ" and you’ll see my copies of newspaper articles from 1969 about this project.

Walsall1955


06/04/14 – 08:22

According to David Harvey’s book on Walsall no. 300 was fitted with a diesel engine under the rear staircase in order to be able to operate away from the overhead – the front entrance was to be widened and the rear platform and staircase removed . Extra trolleybuses were wanted for five additional routes under the terms of a Parliamentary Bill of 1969. I am very pro-trolleybus but why, with the impending PTE takeover, trolleybus expenditure was being pursued at this late date is an interesting question.
Ex Cleethorpes 873 was also subject to engine fitting experiments.

Malcolm Wells


06/04/14 – 10:41

Thx for the additional info, Malcolm. This would explain the hole cut in the offside rear of said trolleybus, which had puzzled me up until now. Here is the link to 300LJ which Walsal1955 mentioned above: www.flickr.com/photos/walsall1955

Chris Hebbron


11/10/14 – 06:01

Walsall 862 at the BCLM – www.youtube.com/watch?v

William Parker

Walsall Corporation – Sunbeam F4 – NDH 958 – 341

Walsall Corporation - Sunbeam F4 - NDH 958 - 341
Copyright Tony Martin

Walsall Corporation
1951
Sunbeam F4
Brush H30/26R

Former Walsall Corporation 341, by August 1970 owned by the West Midlands Passenger Transport Executive, leaves Walsall Bus Station for Blakenhall. It is a Sunbeam F4 with much rebuilt Brush body and should be showing route 15. In the background is former Birmingham City 2593 registration JOJ 593, a 1951 MCW H54R bodied Guy Arab IV, transferred to Walsall in February 1970 with others to partially replace the trolleybuses, though it and its sisters were as old as the vehicles they replaced!

Photograph and Copy contributed by Tony Martin


07/12/12 – 06:55

Nice view, Tony. Thanks for sharing. Others on this site have commented on the full front Vs half cab arrangement of motor buses, citing the amount the driver could or could not see on his nearside – among other factors – yet MOST trolley buses were full front.

Pete Davies


07/12/12 – 08:11

Just speculation but I wonder if the use of full fronts on most trolleybuses was to protect the control gear from water ingress as this was generally on the bulkhead where the engine would be on a motor bus.

Phil Blinkhorn


07/12/12 – 08:12

Surely, Pete, the driver of a Trolley knew that the nearside window was the limit of its width, whereas the problem in the half cab was that the front nearside corner disappeared if a high bonnet obscured the mudguards? Anyone know first hand? Presumably the mirror, if mounted on the nearside corner was a help. Do you remember when you, the driver, could see the front of your car?!

Joe


07/12/12 – 09:56

Actually, Joe, the discussion I remember was about how much less the driver could see with a full front! In the event, the rear engine came along, with the door directly opposite the driver, and the argument was stifled. There was a similar sort of discussion when I was working, and about half the folk who commented said they liked the tip-up seats in shelters and the other half hated them. They went off the market after too many people fell off and the makers’ insurance company jacked up the premium. In a way, I suppose, those who hated the things won.

Pete Davies


07/12/12 – 13:34

I wonder if the issue with full front buses was steaming up in that awkwardly inaccessible left hand cabin. This would probably be more of an issue with the rising emissions from internal combustion engines than the drier warmth from electrical machines. This would not be a problem with rear engine buses of course, and the passenger door gave easy access to the nearside front screen if necessary. I guess everyone will know that the original fleet of Notts & Derbys trolleybuses were half-cabs.

Stephen Ford


08/12/12 – 09:26

I have heard that the cabs of Walsall’s F4As, with their curved glass windscreens gave excellent visibility. There is one behind 341 above and my photo of 872 which is elsewhere on this site.

Tony Martin


08/12/12 – 09:27

A lot of early t/buses were halfcab, because they probably thought they should look like buses. Some even had fake radiators. The 1931 London ‘Diddlers’ were halfcab with a central headlamp on the bonnet front, a la trams!

Chris Hebbron


08/12/12 – 09:28

The Notts & Derby trolleybuses that Stephen refers to had the motor and associated electrical equipment under the bonnet (with ‘dummy’ radiator with the AEC/English Electric badge attached). The London United ‘Diddler’ trolleybuses also had the motor under the bonnet but no attempt was made to provide a ‘dummy’ radiator but there was a single headlamp in the panel where a radiator would have been. There were other instances of trolleybuses with half cabs – Birmingham Corporation for example. Most trolleybuses had the motor located between the chassis side members under the lower saloon floor with a short prop shaft to the rear axle. With this arrangement there was no need to provide a half cab arrangement and the nearside of the full width cab was usually taken up with the contactor cabinet, although some operators, like London Transport, opted to have the contactor cabinet mounted on the nearside of the chassis with access via flap in the vehicle’s ‘skirt’ (or ‘valance’ – depending on which term you choose to use).

Michael Elliott


25/04/18 – 05:41

In Bob Rowe’s new, 2018, book on Walsall Trolleybuses, there is a copy of the tender for the bodies of this batch. Especially interesting is that the Corporation specified that the seats should be covered in leather made in Walsall.

Tony Martin

Walsall Corporation – Sunbeam F4 – ADX 191 – 353

Walsall Corporation - Sunbeam F4 - ADX 191 - 353
Copyright Tony Martin

Walsall Corporation
1950
Sunbeam F4
Park Royal H30/26R

On a snowy day in February 1967 Walsall Corporation trolleybus 353 is on a short working to Leamore. The vehicle was an ex-Ipswich Corporation Sunbeam F4 with Park Royal body which was acquired with seven others due to the closer of the Ipswich Trolleybus system in 1962/3. In the background is the Carl Street entrance to Birchills depot.
But don’t worry, the Summer of Love is just around the corner! (Not that it ever reached Walsall…)

Photograph and Copy contributed by Tony Martin

04/01/13 – 06:49

The Ipswich destination box was an odd shape and it is strange how Walsall retained it, even going to the trouble of having blinds made to fit. With Walsall’s flair for bodywork rebuilding one would have thought they would have rebuilt these to their standard layout.
Accommodating the long word ‘Wolverhampton’ on these blinds meant writing the word diagonally.

Philip Halstead


18/10/13 – 07:41

Used to live about there on Bloxwich Road – watching some of the conductresses trying to switch the points into Carl Street could be amusing, but the sound of a trolley bus starting off from the stop outside our front window has lived with me for 60+ years ….

ex ENOC conductor